无线柄连接不上主机

liatian

斑主留情，因为最近看到有人问这个问题，所以我把我的解决方案直接放上来：
淘宝买根无线手柄的连接线（又称充电线），连上主机就可以再次配对了！此方法只适用于配对模块出问题的手柄，如果这样都不行，那极有可能是您的手柄的无线模块坏掉了！

谁能说一下正确的连接方法？
我试过以下：A开机后，先按主机连接键，再按西瓜键，再按手柄连接键，手柄始终闪烁，连接不成功
B：开机后，先按西瓜键，再按主机连接键，再按手柄连接键，不成功


今天搜了一天，除配对的顺序外，干扰大致分为以下几点：

1.HDMI线的影响，不打开电视，重新配对
2.电源的影响，拔到主机后面的电源数分钟后再次插上，重新配对
3.硬盘的影响，拔掉硬盘，重新配对
4.关掉家里的无线路由，重新配对
5.灰尘的影响，将主机或者手柄RF模块擦干净。重新配对

该用户已被禁言

手柄和主机上有对号键 一起按下         

80318982

     楼上正解！ 不行的话是手柄问题..

liatian

notimetoplay 发表于 2012-7-19 22:02
手柄和主机上有对号键 一起按下

西瓜键是否要先点亮？

liatian

早晨一顶，求支持，求理解

噯噺覺羅痛俓

我也有类似情况，手柄上的西瓜灯在转圈闪灯，然后一会就断开了。。。玩一个游戏重新连接好几次

liatian

顶到问题解决！

该用户已被禁言

liatian 发表于 2012-7-20 07:35
西瓜键是否要先点亮？

当然要有电                        

gh2002hg

噯噺覺羅痛俓 发表于 2012-7-20 08:39
我也有类似情况，手柄上的西瓜灯在转圈闪灯，然后一会就断开了。。。玩一个游戏重新连接好几次

没电了吧。。。。

liatian

谷歌上搜到的，与大家分享一下：
1.HDMI线的影响，不打开电视，重新配对
2.电源的影响，拔到主机后面的电源数分钟后再次插上，重新配对
3.硬盘的影响，拔掉硬盘，重新配对
4.关掉家里的无线路由，重新配对
5.灰尘的影响，将主机或者手柄RF模块擦干净。重新配对

其中最多的就是反应HDMI线的问题，诸如：
If this happens to you, one of two things could be the problem: 1) bad RF board, and 2) HDMI connection.

If you can turn the XBOX on with your controller, the RF boar is fine. If you can't then it is friend and has to be replaced.

Otherwise, it's an HDMI thing. HDMI connections are active, meaning they tell other devices if they are on or off. If your HDMI connection to your XBOX is "off", then it won't start up. In this state, the XBOX will not register a new controller so you can't sync.

Unplugging and removing the HD work because it resets the system settings to standard TV, so you can sync a controller once you turn the XBOX on.

The problem occurs when you try to sync a new controller with the HDMI port off, meaning that the TV is off (Or your receiver if you're using one).

So....if you're having the problem, try syncing with the TV on, or reset the system by unplugging and plugging.

jumpman47 1 solutions Dec 26, 2009
I had a problem with my controller not connecting until I plugged the power cord up and also the rca cables or HDMI, which ever you have, then put the tv on the right input so it could recognize the system. No more connection problems after that....hope that helps somebody.


Entanglebit 3 solutions Feb 23, 2009
If your controller is not assigned a position, and pressing the sync buttons on both the console and the controller don't fix it (i.e. they both spin for a bit, but then the console's lights turn off and the controller's return to a pulsing pattern), the the problem is actually likely to be your TV, believe it or not. The issue is HDMI -- it's a secure connection between the Xbox 360 and the TV, and if there's an issue with that connection, the Xbox won't even be able to turn on since it'll be unaware of the TV's resolution, color capabilities, etc. Try turning off the TV and then turning off the Xbox. Keep the TV off and turn the Xbox console back on. You'll see the same behavior; but now turn the TV back on and you should see the controller get assigned a position. As soon as the Xbox is aware of what it's connected to via HDMI, things start to work again.