- 精华
- 14
- 帖子
- 1259
- 威望
- 14 点
- 积分
- 1841 点
- 种子
- 6 点
- 注册时间
- 2003-11-10
- 最后登录
- 2023-12-1
|
楼主 |
发表于 2004-1-20 15:45 · 北京
|
显示全部楼层
HOW TO ENTER SERVICE MODE
Read the SERVICE MODE WARNING before proceeding.
Service switch - small, round opening in the rear cabinet near the Video inputs or the antenna jack (typically early-90's), push and hold while turning the power on - or if there is no service switch on the rear of the TV use the remote control and press within one second (timing is very important) of each other:
[PWR OFF] - [DISP], [5], [VOL+], [PWR ON]
-or-
[PWR OFF] - [DISP], [5], [PWR ON]
The TV will turn on in service mode and the screen will look something like this:
NAVIGATE IN SERVICE MODE
[1] = Moves to Previous Menu Item
[4] = Moves to Next Menu Item
[3] = Adjusts Value Up
[6] = Adjusts Value Down
[MTS] = Toggles Stereo/Mono Audio
SAVE NEW SETTING
[MUTE] followed by [ENTER] = stores NEW service mode settings to NVRAM
RESTORE USER SETTINGS
[8] followed by [ENTER] = Restores All *USER* settings to factory defaults
RESET VALUES
[0] followed by [ENTER] = Read Default service mode value from stored settings. (service mode reset)
LEAVE SERVICE MODE
[PWR OFF] = Leave Service Mode any settings not written will be in effect until TV is unplugged or a Reset is performed.
RETURN TO DEFAULT SETTINGS:
BEFORE storing NEW settings - unplug TV from wall, wait a few seconds, then plug back in, turn TV set on - All settings not written will have been lost.
AFTER storing NEW settings - restore original value from list you made of original values before adjustments and store in NVRAM.
PLEASE NOTE:
RECORD ALL ORIGINAL VALUES BEFORE
MAKING ANY ADJUSTMENTS.
XBR250 COLOR BANDING PROBLEM
If you have a XBR250 and you're experiencing horizontal blue, green or red banding across the screen with a component video connection, you will need to enter service mode and adjust the HOSC parameter. Initially HOSC is set to 7 (factory default), you'll need to change it to about 11 - this will eliminate the color banding in the picture.
Go Home LIST OF SETTINGS Go Top
ITEM TYPICAL RANGE DESCRIPTION
-------------------------------------------------------------
AFC 0 0-3 AFC Loop Gain
HFRE 42 0-127 Horizontal Frequency
VFRE 11 0-31 Vertical Frequency
VPOS 16 0-31 Vertical Picture Position
VSIZ 18 0-63 Vertical Picture Size
VLIN 6 0-15 Vertical Picture Linearity
VSCO 10 0-15 Vertical Correction
HPOS 6 0-15 Horizontal Picture Position
HSIZ 11 0-31 Horizontal Picture Size
PAMP 18 0-31 Pincushion Amp.
CPIN 4 0-7 Corner Pincushion
PPHA 7 0-15 Pincushion Phase
UPIN 10 0-31 Pincushion upper ends, vertical lines
LPIN 10 0-31 Pincushion lower ends, vertical lines
PPHA 7 0-15 Keystone correction vertical lines
HKEY 6 0-15 Keystone distortion, horizontal lines
HTRP 8 0-15 Keystone correction, horizontal lines
VCOM 2 0-7 Vertical Compensation
VUSN 0 0,1 Shrinks Vertical Height to 16x9 Area
VZOM 0 0,1 Places Bars on Picture to give 16x9 Area
EHT 15 Adjust Height of VZOM
ASP 47 Vertical Picture Size - Aspect
SCRL 31 Vertical Picture Position
HBLK 1 0,1 Horizontal Blanking (on/off)
LBLK 15 Left Blanking
RBLK 3 Right Blanking
GAMP 18 0-31 Green Amp.
BAMP 14 0-31 Blue Amp.
GDRV 18 0-31 Green Driver
BDRV 14 0-31 Blue Driver
RCUT 15 Red Cutoff - (lower level)
GCUT 4 0-15 Green Cutoff - (lower level)
BCUT 1 0-15 Blue Cutoff - (lower level)
RDRV 21 Red Amp. - (upper level)
GDRV 18 Green Amp. - (upper level)
BDRV 14 Blue Amp. - (upper level)
DCOL 1 0,1 Color Temperature
COFF 0 0,1 Color On/Off - B/W Picture
Y-DC 0 0-15 BLACK background level retention
R-YR 15 0-15 Sets the amount of RED
R-YB 15 0-15 Sets the amount of RED
G-YG 11 0-15 Sets the amount of GREEN
G-YB 9 0-15 Sets the amount of GREEN
AXIS 0 0-15 Cleans up the red & oranginess in yellow
DPIX 0 0-3 Dynamic Picture
CROM 28 0-63 Chroma Trap
SPIX 30 0-63 Sub-Picture Contrast (Picture)
SCON 30 0-63 Sub-Picture Contrast (Picture)
SHUE 23 0-63 Sub-Picture Hue
SCOL 26 0-63 Sub-Picture Color
SBRT 22 0-63 Sub-Picture Brightness (Black Level)
RGBP 10 0-63 RGB Picture
SHAP 6 0-15 Sub-Picture Sharpness
SHPF 3 0-15 This helps with the S-Video sharpness
NRLV 0 0-3 Find the value that gives the best resolution
VSMO 1 0,1 Vertical Pull In Range (1 allows PAL in B&W)
REF 2 0-3 Reference Line
ROFF 1 0,1 Red Gun ON(1)/OFF(0)
GOFF 1 0,1 Green Gun ON(1)/OFF(0)
BOFF 1 0,1 Blue Gun ON(1)/OFF(0)
RON 1* 0,1 Red Gun ON(1)/OFF(0)
GON 1* 0,1 Green Gun ON(1)/OFF(0)
BON 1* 0,1 Blue Gun ON(1)/OFF(0)
AXPL 0 0,1 Cleans up Reds/Yellows
ABLM 0 0,1 Automatic Background or Brightness Limiter
NOTC 1 0,1 Notch Filter ON(1)/OFF(0)
VMLV 0 0,1 Scanning Velocity Modulation ON(1)/OFF(0)
VAPI 0 0,1 Sets vert resolution for 3-d comb filter
VAPG 0 0,1 Sets vert resolution for 3-d comb filter
DRGB 0 0,1 On-Screen Display (OSD) Intensity
DISP 35 0-63 On-Screen Display (OSD) Menu Placement (L/R)
VTMS 0 0-3 On Screen Display (OSD) - On/Off
DPDV 1 0-3 Lumipon
MPIC 8 0-63 Lumipon (depth)
SVOL 0 0-15 Sub-Volume (0=Max,15=Min.)
SBAL 7 0-15 Sub-Balance (0=Left,15=Right)
BASS 8 0-15 Sub-Bass (0=Min., 15=Max.)
TRE 7 0-15 Sub-Treble (0=Mix., 15=Max.)
MPX - 0-15 Audio ATT
FILO - 0-15 Audio I1
DEEM - 0-15 Audio I2
STEV - 0-15 Audio OSC1
SAPV - 0-15 Audio OSC2
PILO - 0-15 Audio PILOT
SEP - 0-15 Audio WIDE BAND
VD - 0-15 Audio SPECTRAL
LVOL - 0-15 Audio VOLUME-L
RVOL - 0-15 Audio VOLUME-R
PADJ 63 0-255 Hor/Vert Picture Adjustment (total picture)
UYBO 32 0-63 Upper Y Bow (B/R Top)
LYBO 27 0-63 Lower Y Bow (B/R Bottom)
HAMP 34 0-63 Horizontal Amp. (B/R OuterLines)
HTIL 32 0-63 Horizontal Tilt (R/R)
UCBO 39 0-63 Upper C Bow (B/R Corners Only)
UTIL 37 0-63 Upper Tilt (Top Corners)
LCBO 41 0-63 Lower C Bow (B/R Corners Only)
LTIL 40 0-63 Lower Tilt (Bottom Corners)
DCSH 36 0-63 DC Shift (Static Convergence All Vertical)
VBOW 30 0-63 Bow distortion correction vertical lines
VANG 30 0-63 Skew correction, vertical lines
RTCO - 0-63 Raster Rotation
PHPO 79 0-127 Picture In Picture (PIP) Horizontal Position
PHUE 0 0-31 Picture In Picture (PIP) Hue
MSHU - 0-31 Main PIP hue
MSCOL - 0-31 Main PIP color
SSHU - 0-31 Small PIP Hue
SSCO - 0-31 Small PIP Color
GV SKEW - 0-63 convergence service item
GH SKEW - 0-63 convergence service item
GH BOW - 0-63 convergence service item
RV SKEW - 0-63 convergence service item
BV SKEW - 0-63 convergence service item
GH PIN - 0-63 convergence service item
GH CENT - 0-63 convergence service item
GV CENT - 0-63 convergence service item
RH CENT - 0-63 convergence service item
RV CENT - 0-63 convergence service item
BH CENT - 0-63 convergence service item
BV CENT - 0-63 convergence service item
ID0 88 0-127 Model ID
ID1 127 0-127 Model ID
ID2 104 0-127 Model ID
ID3 64 0-127 Model ID
ID4 19 0-127 Model ID
ID5 1 0-127 Model ID
NOTE:
Not all ITEMS appear on all televisions models.
Provisions for convergence adjustments are not enabled on 27" or smaller Sony direct view television sets.
Typical settings may not apply to your particular model and are shown only for reference purposes.
Go Home SUGGESTED SONY SETTINGS Go Top
SONY "XBR" SERIES
TRINITONE: NTSC STD - controls color temperature - basically how greys will appear on the monitor. The "High" and "Medium" settings make everything look too blue.
NR: OFF - filters out high-frequency noise, at a slight loss of detail. Turn it OFF and the picture quality improves. It also tends to degrade fine picture detail.
DYNAMIC PICTURE: OFF - when turned ON it whitens light areas and darkens shadow areas of the picture, creating a high contrast although less accurate picture. Leave it OFF.
COLOR CORRECTION: OFF - when turned ON it tries to correct fleshtones but has a tendency to mix up certain colors and make them look like a prosthetic beige.
PROGRAM PALETTE: MOVIE: ON - only the movie mode allows the television set to run with flat and wide video bandwidth. It also shuts OFF scanning velocity modulation (SVM), when VMLV is run down to zero it will shut OFF SVM for the other modes. Each mode (Movie, Sports, etc.) has a separate adjustment memory.
SERVICE MODE ITEMS:
AXIS 0 Cleans up the red push & oranginess in the yellows
VAPI 0 Sets vert resolution for 3-d comb filter
(do this for all modes)
VAPG 0 Sets vert resolution for 3-d comb filter
(do this for all modes)
NRLV 0~3 Find the value 0-3 that gives the best resolution
VMLV 0 Scanning Velocity Modulation (SVM) OFF=0/ON=1
(do this for all modes)
Y-DC 0 Improves BLACK background level retention
DCOL 0,1 Color Temperature - Select either 0 or 1 whichever
turns off the "blue tinted" whites.
DPIX 0 Dynamic Picture
AXPL 0 Cleans up Reds/Yellows
GDRV 18 (GAMP) Green Amp. - (upper level)
BDRV 14 (BAMP) Blue Amp. - (upper level)
GCUT 4 Green Cutoff - (lower level)
BCUT 1 Blue Cutoff - (lower level)
R-YR 15 Sets the amount of RED
R-YB 15 Sets the amount of RED
G-YR 11 Sets the amount of GREEN
G-YB 9 Sets the amount of GREEN (8 or 10 may be closer)
SHPF 3 This helps with the sharpness (S-Video)
Setting R-YR and R-YB to 15 will greatly improve color accuracy and tone down the reds. Also, when Y-DC is changed from 1 to 0, DC restoration (black level retention) becomes almost perfect.
Sometimes setting items G-YR to 11 and G-YB to 9 may need some more fine tuning using the SMPTE color bars w/gray reference [split bar pattern] (Frame VE-46673, AVS-14415 - NOTE: VE 46673 is mis-calibrated, use AVS-14415) See the section on Setting Tint & Color Level: Matching Gray Reference in the How to Calibrate a Television FAQ for the procedure on how to adjust these two settings.
WEGA SERVICE MODE ITEMS:
4BCT 7 input4 (component) Blue Cutoff (BCUT -1)
4BDR 30 input4 (component) Blue Amp (BDRV +1)
4GCT 5 input4 (component) Green Cutoff (GCUT +0)
4GDR 36 input4 (component) Green Amp ((GDRV +2)
BCUT 10 Blue Cutoff
BDRV 29 Blue Amp
GCUT 10 Green Cutoff
GDRV 34 Green Amp
DPIX 0 Dynamic Picture
Y-DC 0 Improves BLACK background level retention
HOSC 11 Fixes problem with color banding on component input
SONY "MODEL-ID" SETTINGS
These ID setting are different for every chassis - in general here's what they control:
ID-0 Controls number of active video jacks.
ID-1 This controls video features. Allows notch filter
(NOTC) to be turned off outside of service mode.
ID-2 This sets up user interface features. Enables Spanish
language menus. Allows naming of video inputs.
ID-3 Enables / disables Picture-In-Picture (PIP) support.
ID-4 Enables / disables Lumisponder option. |
|
楼主: 沙卡卡
[复制链接]
川公网安备 51019002005286号
发表于 2004-1-19 12:46 · 山东
